Idex-health-science Flowmaster – version with Timer Function Uživatelský manuál

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 1English FrançaisDeutschBetriebsanleitungOperating ManualMode d‘emploi11.07.07 CB/GPSchlauch-pumpeMikropro

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 10Pumping 1 Set the required rotation speed (in rpm or %) with the 56 keys2 Enter the rotation direction

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 11Pumping with timer function1 When the pump is idle, you can switch between pumping and timer function by

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 12When the pump is idleWhen the pump is idle, we rec- ommend you to release the tubing from pressure. Open

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 13Max. operating pressureInformation supplied by the tubing manufacturersOverload protectorThe Flowmaster p

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 14Operating panel1 Power supply switch (on/off)2 Digital LED display3 5Key – Increase speed – Increase

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 15OverviewBasic settingsThe following basic settings can be entered in the 'Settings' menu:Autost

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 16Selecting the basic settings1 Push the settings key whilst switching the pump on, or if the pump is swi

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 17Autostart konfigurierenConfiguring AutostartConfiguration de démarrage automatique Standby: Pumpe steht beim

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 18Grundeinstellungen Menüstruktur / Settings Menu Map / Diagramme des menus de réglagesAnalogschnittstelle

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 19Grundeinstellungen Menüstruktur / Settings Menu Map / Diagramme des menus de réglagesin min-1in rpmen t/m

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 2ContentsSafety precautions 4Warranty terms 6Product 7Rear panel 8Mains voltage 9Starting the pump

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 20Settings MenuOptionenOptionsOptionsAnzeige BetriebsstundenzählerDisplay of running time meterAffichage du

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 21okdefaulta b cSettings Menu MapTubing life expectancyIf this mode is active, the pump warns you when the

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 22Analog interfacePin 1, +24 VDC, 0.5 AAuxiliary voltage for peripherals (max. current 0.5A)Pin 2, status

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 23Analog interfacePin 10, status okIf the pump is switched on and provided there is no error, this output i

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 24Lebensdauer der SchläucheDie Lebensdauer hängt stark von den jeweiligen Anwendungsbe-dingungen in Kombin

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 25MaintenanceProvided the pump is operated properly and in compliance with this manual, the tubing is the o

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 26Opening the casing In order to maintain the best possible seal of the casing, the pump should only be o

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 27Opening the casing 3. Press the casing hood down-wards and fasten the screws evenly from top to bottom.

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 28Disassembling the pump head1. Open the pump head with the lever. Remove the tubing.2. Loosen the two sc

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 29Disassembling the pump head5. Pull the button at the hinge. Remove the tube bed by pulling it upwards.6.

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 3 Netzanschluss230 VAC Absicherung min. 10A115 VAC Absicherung min. 20A Mains supply230 VAC fuse

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 30Assemblingthe pump head1. Slip the torsion spring (b) over the ball bearings (a). Position the endings o

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 31Assemblingthe pump head5. Put the covering plate in place and fix it with the two screw plugs. Insert the

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 32Plug gasketsIf the interface port is used under IP 65 conditions, the originally supplied gasket must b

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 33 HinweisBeachten Sie ebenfalls unsere Garantie- und allgemeinen Verkaufs- und Lieferbe-dingungen.Bitte

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 34AppendixActivating a foot switchTwo foot switch modes are avai-lable:– FSt0 (Toggle mode) The pump is

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 35AppendixActivating a foot switch6 – Select LOGI with the 56keys – ok (confirm your selection)7 –

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 36ISMATEC® - Ihr kompetenter Partner für anspruchsvolle Pump- und Dosieraufgaben. ISMATEC® - Your competen

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 4Safety precautionsISMATEC® Pumps are designed for pumping applications inlaboratories and industry. As su

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 5 Transportieren der PumpeDie Pumpe hat ein Gewicht von 26 kg.Sie soll grundsätzlich mit einem Hilfsmitte

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 6Warranty termsWe warrant the perfect function-ing of our products, provided they have been installed and

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 7Product Contents of the package1 Flowmaster drive Order No. ISM 1020 incl. integrated power cord, 2 m

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 8Rear panel1 Cover plate for the fuses and the voltage selector 115 / 230 V2 Power cord3 Analog interfa

Flowmaster / ISMATEC SA / 11.07.07/CB/GP 9Starting the pump1. Open the tube-bed by lifting the lever and insert the tubing into the pump head2.Close